H&S Model 3131

H&S Model 3131 for sale at Red Power Team, Iowa

Double tap to zoom

Features
Specs

Features

A massive unitized welded frame with heavy floor supports and side stakes, wrap around steel front corners. Strong rear main beater side panels are slanted for clearance and wider spread, and then welded to the strong 5″ U channel side members compare with any on the market.
The side flares on all H&S “Heavy Duty” manure spreaders are made of 10 gauge g210 culvert grade galvanized steel.
Sides, front panel and both sides of the rear hydraulic end gate use fiberglass reinforced plywood to provide for easy cleaning and minimal freeze up. It also features a solid virgin grade poly floor. Considerably less torque is needed to move a heavy load.
A front splash guard is standard equipment.
Greaseable bearings.
The two-speed apron drive is standard equipment. An optional variable speed hydraulic drive is also available. As is an optional electric control for the hydraulic drive.
A 29″ diameter beater with 14 replaceable beater paddles. The beater has two types of paddles, blunt for widespread and sharp ripper type for cutting and shredding. The beater side wiper blades are also standard equipment.
The hydraulic endgate features 2 cylinders as standard (optional on the 3131). The hydraulic lines are run through a 3×3 tube under the floor. The upright position of the hydraulic cylinder stroke allows the gate to lift with the least strain at pivot points.
H&S uses cast special steel alloy apron idler slides instead of idler sprockets making for years of dependable service.
Adjustment for the main apron is easy by simply loosening the two side bolts and drawing up the long bolt.
Gear box mechanisms and drive for the beater and apron are Timken tapered roller bearing equipped. The beater drive gear box is 1-½″ bevel gear oil bath equipped with a 4-jaw over running clutch for beater shut off. The apron drive is a 50:1 bronze worm gear with shear bolt protection.
The strong oil bath bevel gear box that powers the beater is tapered Timken roller bearing equipped. The gear box utilizes a 4-jaw beater shut off clutch and tractor sized spline shaft.
Unloading Speed for 3131, 3137, 3143, and W3143 – (2 speed chain drive) High Speed: PTO speed 540 rpm’s 8′8.5″ per minute Low Speed: PTO speed 540 rpm’s 4′8.5″ per minute.
An optional top beater is available to provide load leveling and spreading of high heaped loads. (Standard in models 3143 & W3143)
The W3143 (western) has all the same features as above with additional features such as double main frame channels, additional floor supports, 1045 hardened drive shaft, #80 drive chain and a heavy duty main gear box.

Specs

MODEL	3131
CAPACITY - OLD RATING	310 B.U.
CAPACITY CU. FT. STRUCK LEVEL	185
TOP OF FLARE WIDTH	68″ (173 CM)
INSIDE WIDTH	60″ (152 CM)
INSIDE LENGTH	15′ 7″ (4.8 M)
INSIDE DEPTH	28 ⅜″ (72 CM)
OVERALL WIDTH W/STANDARD TIRES	98″ (249 CM)
OVERALL LENGTH	21′ 11.5″ (6.7 M)
OVERALL LOADING HEIGHT-TOP OF FLARE	51.5″ (131 CM)
OVERALL HEIGHT W/HYD. ENDGATE	55″ (140 CM)
DIAMETER OF BEATER	29″ (74 CM)
MAIN APRON CHAIN	T-ROD
UPPER BEATER	OPTIONAL
SPINDLE SIZE	2 ¼″ (6 CM)
STANDARD TIRE SIZE	295x22.5 RECAP
WEIGHT W/TIRES	4190# (1,901 KG)
REAR HYDRAULIC ENDGATE	STANDARD
SEMI LIQUID REAR PAN	OPTIONAL
PTO SPEED	540 STANDARD 1000 OPTIONAL
JACK	STANDARD
DRIVE	2 SPEED
VARIABLE SPEED HYD. DRIVE	OPTIONAL
FRONT SPLASH PANEL	STANDARD
HYD. CYL ON HYD. ENDGATE	1-STANDARD 2ND OPTIONAL

Amount Financed ($)
Interest Rate (%)
Loan Term in Months
Monthly Payment	Calculated

Loan Calculator

Features

Specs

USED EQUIPMENT

NEW PRODUCTS

GOT A QUESTION?

H&S Model 3131

Heavy Duty Manure Spreaders Model 3131

Get A Quote

Request Brochure

Send To A Friend

Loan Calculator

Features

Specs

USED EQUIPMENT

NEW PRODUCTS

GOT A QUESTION?